Vehicle report

2021 Ford Bronco

Recalls, consumer complaints, safety ratings, fuel cost estimate, and next steps from official public data sources.

2021 Ford Bronco
19 Total recalls
May 12, 2026 Latest recall date
211 Complaint reports
$2,590 Estimated fuel cost
Quick answer: The 2021 Ford Bronco has 19 official recalls and 211 consumer complaints in our database. The latest recall date is May 12, 2026. The most common complaint categories include engine, suspension, unknown or other. Estimated annual fuel cost is $2,590 based on the current calculator assumptions.

Buyer interpretation

What this record means before you buy

The useful question is not just whether this page has records. It is what those records should make you verify before money changes hands.

Recall homework

There are 19 official recalls listed for this model year. Before buying, use the VIN to confirm which campaigns are still open and ask for dealer repair records on completed work.

Owner complaint pattern

Owner complaints most often mention engine, suspension, unknown or other. Scan those categories before the test drive so you know what symptoms, warning lights, or service history to ask about.

Service bulletin signal

453 manufacturer communications are listed. These are not recalls, but they can reveal repair instructions, warranty extensions, software notices, or known service patterns.

Ownership-cost check

The fuel-cost estimate is based on a representative EPA match, not every trim. Confirm the actual engine, drivetrain, and tire setup before comparing this listing with another year or model.

Questions to ask the seller

  • Can you show the current VIN recall status for this 2021 Ford Bronco?
  • Do you have dealer invoices or campaign paperwork for the listed recall repairs?
  • Have you noticed any issues related to engine, suspension, unknown or other?
  • Can I review recent maintenance records before the test drive?
Used-car checklist

Thinking of buying this vehicle?

Use our buyer checklist to know what to inspect, ask, and verify before the test drive.

2021 Ford Bronco Regular Gasoline
Create checklist Compare with other years Sends year, make, and model to pre-fill your checklist.

Safety ratings

Official safety ratings were found for 2 tested variants of the 2021 Ford Bronco.

Overall Not Rated
Frontal crash Not Rated
Side crash Not Rated
Rollover 3/5 stars

Displayed variant: 2021 Ford Bronco 4DR SUV 4WD ; rollover risk 25.6%

Safety ratings can vary by tested body style, trim, drivetrain, or variant. Do not assume every trim has the same rating unless the official record says so.
Variant Overall Front Side Rollover
2021 Ford Bronco 4DR SUV 4WD Default Not Rated Not Rated Not Rated 3/5 stars
2021 Ford Bronco 2DR SUV 4WD Not Rated Not Rated Not Rated 3/5 stars

How many recalls does the 2021 Ford Bronco have?

Verify with official VIN lookup

19 official recalls on record for the 2021 Ford Bronco. 83 matched quarterly completion reports are available.

Latest recall: May 12, 2026

Recall data is based on official records. This page is not an official VIN recall check. Always confirm open recalls with an official VIN lookup, the manufacturer, or an authorized dealer. Completion reports are campaign-level, delayed, and not VIN-specific.
Campaign Component Summary Consequence Remedy Date Completion
26V299000 STRUCTURE:BODY:ROOF AND PILLARS Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The 3-door and 5-door Molded-In-Color (MIC) hardtop roof panels may have been manufactured improperly, which can allow sections of the outer roof panel to separate and detach from the vehicle. A detached section of roof can create a road hazard, increasing the risk of a crash. Dealers will inspect and replace the hard top as necessary, free of charge. Interim letters, notifying owners of the safety risk are expected to be mailed May 27, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S32. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 12, 2026. May 2026 Not matched
26V236000 POWER TRAIN:AUTOMATIC TRANSMISSION Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer case input splines. Excessive wear of the transmission and transfer case splines may result in a loss of drive power or vehicle rollaway, increasing the risk of a crash. Dealers will inspect the transmission to transfer case joint and replace the transmission and transfer case as necessary, free of charge. Interim letters, notifying owners of the safety risk, are expected to be mailed April 27, 2026. Additional letters will be sent once the remedy is available, anticipated in July 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S26. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026. Apr 2026 Not matched
26V124000 BACK OVER PREVENTION:SOFTWARE Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended. A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash. The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026. Mar 2026 Not matched
25V888000 BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility." A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash. Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026. Dec 2025 2026-1
4 remedied / 35 involved (11.4%)
25V721000 SEATS:CRITICAL FASTENERS Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt. A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury. Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed April 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB5. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025. Oct 2025 Not matched
25V685000 EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in. An electrical short circuit can increase the risk of a fire. Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025. Oct 2025 Not matched
25V455000 FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving. An engine stall increases the risk of a crash. The remedy is under development. Interim notification letters notifying owners of the safety risk were mailed July 16, 2025. Second letters will be sent once the remedy is available, anticipated 2nd Quarter 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S75. Jul 2025 Not matched
25V315000 BACK OVER PREVENTION:SOFTWARE Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse. A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash. The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49. May 2025 2026-1
817,260 remedied / 1,076,138 involved (75.9%)
25V312000 BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility." A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash. Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14. May 2025 2026-1
174 remedied / 12,219 involved (1.4%)
25V025000 SUSPENSION:REAR:SHOCK ABSORBER Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir. An external reservoir that detaches from a vehicle can create a road hazard, increasing the risk of a crash. Dealers will replace the rear shock absorbers, as necessary free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S01. Jan 2025 2026-1
70,504 remedied / 149,449 involved (47.2%)
24V635000 ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power. A loss of drive power increases the risk of a crash. Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55. Aug 2024 2026-1
52,222 remedied / 90,736 involved (57.5%)
23V598000 BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Ford Motor Company (Ford) is recalling certain 2020-2023 Lincoln Aviator, 2018-2021 Lincoln Navigator, 2022-2023 Ford Transit, and 2021 Ford Bronco vehicles. The rearview camera, or 360-degree view camera if equipped, may not display a rearview image when the vehicle is placed in reverse. Loss of the rearview camera image can reduce the driver's rear visibility, increasing the risk of a crash. Dealers will replace the rearview camera, and update the software and wiring as necessary, free of charge. Owner notification letters were mailed November 20, 2023 to Lincoln owners. Ford vehicle owners notification letters were mailed March 4, 2024. Ford remedy parts are anticipated 2nd Quarter 2024. Ford's number for this recall is 23S48. Aug 2023 2025-3
126,269 remedied / 177,402 involved (71.2%)
23V358000 SEAT BELTS:CRITICAL FASTENERS Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection." Difficulty accessing the seat belt latches may result in occupants not wearing their seat belts, increasing the risk of injury in a crash. Dealers will add a sliding clip latch stop to the driver and front passenger seat belts, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed July 14, 2023. Owner letters informing owners that parts are available were mailed on October 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C16. May 2023 2025-2
124,852 remedied / 175,550 involved (71.1%)
23V165000 BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility." A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash. The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05. Mar 2023 2025-3
1,285 remedied / 1,651 involved (77.8%)
22V928000 AIR BAGS:SENSOR:SIDE IMPACT Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle. An improperly secured side impact sensor may cause the air bags to unintentionally deploy, or not to deploy as intended, increasing the risk of injury in a crash. Dealers will inspect the side impact sensor attachments and repair, as necessary, free of charge. Owner notification letters were mailed January 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S77. Dec 2022 2024-4
1,004 remedied / 1,226 involved (81.9%)
22V825000 BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility." A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash. The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27. Nov 2022 2025-2
41,079 remedied / 47,046 involved (87.3%)
22V411000 LATCHES/LOCKS/LINKAGES:DOORS:LOCK Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position. A malfunctioning child safety lock increases the risk of injury to a child occupant. Dealers will inspect the passenger-side child safety locks door child safety lock and latch, and replace them, if necessary, free of charge. Owner notification letters were mailed June 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S44. Jun 2022 2024-4
43,750 remedied / 53,103 involved (82.4%)
21V982000 FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: RADAR Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production. A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash. Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52. Dec 2021 2023-4
574 remedied / 839 involved (68.4%)
21V770000 AIR BAGS:FRONTAL Ford Motor Company (Ford) is recalling certain 2021 Bronco vehicles. During passenger air bag deployment, an air bag vent could open prematurely and result in an improper deployment. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection." Improper air bag deployment increases the risk of injury during a crash. Dealers will replace the passenger air bag, free of charge. An interim owner notification letter was mailed on November 24, 2021. A second notice announcing the remedy is available was sent on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C23. Oct 2021 2024-1
445 remedied / 553 involved (80.5%)

Are there federal defect investigations for the 2021 Ford Bronco?

Official records show 6 federal defect investigations matched to the 2021 Ford Bronco.

0 open 6 closed
Investigations are not recalls. They show official defect reviews and may close without a recall, or may reference a related campaign when one exists.
Action Status Component Subject Opened Related recall
RQ24014 Closed ELECTRICAL SYSTEM:12V/24V/48V BATTERY Loss of Motive Power
On January 31, 2024, The Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24002) to investigate loss of motive power allegations in model year (MY) 2021 Ford Bronco Sport vehicles. Consumers reported a loss of engine power accompanied by complete electrical system failure either while driving or after stopping at a traffic light or stop sign. The vehicles generally could not be restarted, and the incidents were commonly diagnosed by dealerships to a failed 12-Volt (12V) battery. On April 12, 2024, Ford issued safety recall 24V-267 covering 456,565 MY 2021-2024 Ford Bronco Sport and MY 2022-2023 Ford Maverick vehicles. The recall addressed loss of motive power resulting from sudden degradation of the 12V battery during the drive cycle. The recall remedy consisted of software updates to the body control module and the powertrain control module. The updated software aimed to provide warning to consumers when the battery is failing and inhibit certain vehicle functions which can lead to loss of motive power incidents. Additionally, Ford removed the existing 12V Enhanced Flooded Battery (EFB) as both a service component for the subject vehicles and original equipment for newly built Bronco Sport vehicles (during MY 2024 production), replacing it with a more robust absorbed glass mat (AGM) battery. The same AGM battery had been incorporated into Ford Maverick production in late 2022. Following recall 24V-267, ODI received loss of motive power complaints in vehicles that had previously received Ford’s software-based remedy. Consumers reported that they did not receive warnings related to the 12V battery or the vehicle’s electrical system before the loss of power. On November 15, 2024, ODI opened Recall Query (RQ24014) to assess the effectiveness of the 24V-267 recall remedy. On January 19, 2025, Ford issued recall 25V-019 covering 272,817 MY 2021-2023 Bronco Sport and MY 2022-2023 Ford Maverick vehicles. The new recall addressed the same hazard as 24V-267 but required replacement of the existing 12V battery with an AGM battery as the remedy. Ford reported that following the opening of RQ24014, it evaluated several field-returned 12V batteries, and determined that EFBs produced by battery supplier Camel potentially contained internal manufacturing defects causing loss of motive power. Ford further concluded that the software updates provided in the 24V-267 recall remedy were unable to detect battery failures quickly enough to avoid loss of motive power. Vehicles previously within the scope of recall 24V-267, but outside of the scope of recall 25V-019, are equipped with EFBs produced by a different battery supplier (Clarios). When recall 25V-019 was issued, Ford had not identified any Clarios EFBs exhibiting the same failure mode as the Camel EFBs. In light of Ford’s recall action, ODI is closing this Recall Query. The agency will continue to monitor loss of motive power complaints in Bronco Sport vehicles equipped with Clarios EFBs and reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Nov 2024
Closed Oct 2025
25V019
PE24019 Closed FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP Low-pressure fuel pump failure
On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the affected vehicles may lose fuel pressure and flow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford filed recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Jul 2024
Closed Sep 2025
None
PE24002 Closed ELECTRICAL SYSTEM:12V/24V/48V BATTERY Loss of Motive Power
On January 31, 2024, the Office of Defects Investigation (ODI) opened PE24002 to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco Sport vehicles. At that time, ODI had received 31 Vehicle Owner Questionnaires (VOQs), with consumers commonly reporting a loss of engine power accompanied by complete electrical system failure which occurred either while driving, or after coming to a stop. The investigation revealed that MY 2021-2024 Ford Bronco Sport and certain MY 2022-2023 Ford Maverick vehicles are equipped with a 12V enhanced flooded battery (EFB), which may experience an abrupt failure during a drive cycle. The failure is the result of an internal corrosion issue, which is influenced by long exposure to high under-hood temperatures. If the sudden loss of 12V battery voltage is not detected by the vehicle’s battery management sensor, the vehicle can experience a loss of power event without providing any warning to the driver. Following a loss of power due to battery failure, the vehicle may be without all 12V accessories including hazard lights and typically will not be able to be restarted. In its March 2024 response to ODI’s information request, Ford provided 367 customer complaints (including field reports, lawsuits, and legal claims) and 1005 warranty claims relating to the alleged defect. When combining ODI and manufacturer failure report data, there are 1,368 unique VINs represented across MY 2021-2023 Ford Bronco Sport vehicles. One of the VOQs submitted to NHTSA reported a minor rear-end collision resulting from a loss of power event. Included within Ford’s complaints were a reported single-vehicle collision and a vehicle fire which occurred following a loss of power event at a traffic light (fire cause and origin was not determined). Additionally, across ODI and manufacturer data, there were 12 allegations of either acid leaking from the 12V battery or smoke emitting from the battery area within the engine compartment. On April 12, 2024, Ford submitted recall 24V267 for MY 2021-2024 Ford Bronco Sport and certain MY 2022-2023 Ford Maverick vehicles (total population 456,565). The recall remedy provides updated calibrations to the body control module and powertrain control module. Ford indicated that the update will result in improved detection of 12V battery state of charge during drive cycles and will provide notification to the driver if the battery significantly degrades while driving. Additionally, Ford has replaced the EFB with an absorbed glass mat (AGM) battery as both a service component for the subject vehicles and as original equipment for Bronco Sport vehicles with production dates beginning in mid-March 2024. The warranty claim rate for peer vehicles equipped with an AGM battery is substantially lower than that for the subject vehicle population. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Jan 2024
Closed Aug 2024
24V267
EA23002 Closed ENGINE Loss of Motive Power
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family.  If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Sep 2023
Closed Oct 2024
24V635
PE22007 Closed ENGINE Loss of motive power due to valve intake failure on Ford Bronco vehicles.
The Office of Defects Investigation (ODI) received a petition dated March 16, 2022, requesting an investigation regarding allegations of defective intake valves in model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost (“Nano”) engines.  The petitioner alleged these vehicles are experiencing loss of motive power at any highway speeds with no-restart as a result of catastrophic engine failures.  To date ODI is aware of 42 submitted Vehicle Owner Questionnaires (VOQ’s) alleging a loss of motive power. On July 22, 2022, ODI opened a Preliminary Evaluation (PE22-007) to investigate allegations of stalling/loss of motive power on the subject vehicles.  Upon receiving Ford’s Information Request (IR) response, ODI learned Ford was aware of 110 consumer complaints (including field reports), 125 warranty claims and 136 engine exchanges related to the 2021 Ford Bronco.  Ford’s response indicated these failures are across the “Nano” engine family, which includes both the 2.7L and 3.0L EcoBoost engine variants with a total estimated population of 708,837 vehicles. Additionally, ODI became aware that the subject engines contained intake valves that were manufactured out of a specific alloy known as “Silchrome Lite”, which can become excessively hard and brittle if an over-temperature condition occurs during machining of the component. The overly brittle intake valve can fracture at the keeper grove causing the intake valve to freely contact the piston, resulting in catastrophic engine failure.  A design modification was implemented in October 2021, which changed the intake valve material to a different alloy known as “Silchrome 1”, that is less susceptible to over-temperature during machine grinding. ODI is upgrading this PE to an Engineering Analysis (EA23-002) to better understand the failure mechanism identified by Ford and to ascertain the complete scope.  To review the reports cited in the attached Closing Resume ODI Report Identification Number document, go to NHTSA.gov
Jul 2022
Closed Oct 2023
None
DP22001 Closed ENGINE Loss of Motive Power
The Office of Defects Investigation (ODI) received three petitions on March 17, March 18, and March 29, 2022, which requested a defect investigation into an alleged defect of the valves on model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost engines. The petitioners alleged that MY 2021 Ford Broncos vehicles are experiencing loss of motive power at highway speeds with no-restart due to catastrophic engine failures.On May 27, 2022, ODI opened this Defect Petition to evaluate whether to grant or deny the petition.ODI has identified 26 Vehicle Owners Questionnaires (VOQs) that relate to the alleged defect in the subject vehicles. Based on ODI's review of the applicable materials, including VOQs, NHTSA has decided to grant the petition and open a Preliminary Evaluation (PE22-007) to assess the scope, frequency, and potential safety-related consequences of the alleged defect.Accordingly, this Defect Petition is closed.The ODI complaints cited above can be reviewed at NHTSA.gov under the following ODI numbers:11448171, 11448461, 11450659, 11450702, 11450737, 11450788, 11450871, 11450879, 11451158, 11451503, 11451957, 11452074, 11452692, 11453669, 11453933, 11454098, 11455294, 11456219, 11456713, 11459262,11460124, 11460125, 11461178, 11463199, 11463296, 11464516.
May 2022
Closed Jul 2022
None

Are there manufacturer notices for the 2021 Ford Bronco?

Official records show 453 manufacturer communications on record for the 2021 Ford Bronco.

0 warranty 0 service campaigns 12 software/OTA

Common components: UNKNOWN OR OTHER (106), ELECTRICAL SYSTEM (82), EQUIPMENT (62), POWER TRAIN (57), ENGINE AND ENGINE COOLING (31)

Manufacturer communications are not recalls. They can include service bulletins, repair instructions, warranty extensions, software updates, service campaigns, and other notices.
Date Type Component Summary ID / document
May 2026 Service Bulletin/Repair Instructions FUEL/PROPULSION SYSTEM 2020-2026 Explorer/Escape/Corsair, 2021-2026 Bronco Sport/Bronco, 2022-2026 Maverick, 2024-2026 Mustang/Ranger/Nautilus vehicles equipped with a 2.0L or 2.3L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 2.0L/2.3L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure been added. In addition, the wastegate actuator rod (9E408), associated retention springs (9342) and retaining clips (00817) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate actuator assembly. 11032924
SSM 54857
May 2026 Service Bulletin/Repair Instructions UNKNOWN OR OTHER This bulletin supersedes 25-2346. Reason for update: add Bronco Sport and Escape vehicles and add labor operations to repair the rear right/left carpet area. Some of the vehicles listed in the Model statement above may exhibit a condition where the carpet is loose or torn near the front/rear scuff plate trim panel. This may be due to the carpet tearing at or near the retainer hole. 11032746
TSB 26-2205
May 2026 Service Bulletin/Repair Instructions POWER TRAIN Some 2021-2024 Bronco vehicles equipped with a manual transmission may experience a rotational scraping noise while the transmission is in neutral, 1st and/or 2nd gear with the clutch pedal released. The noise may be more noticeable in ambient temps below 10°C (50°F) and after a cold soak. This noise may also diminish as the transmission warms up. This may be due to the 5th and 6th gear synchronizer rings. The 5th and 6th gear synchronizer rings are now only available in the 6th/5th gear synchronizer assembly (service part number MU7Z-7124-Q). To correct the condition, replace the 6th/5th gear synchronizer. Remove the transmission from the vehicle. Refer to Workshop Manual (WSM), Section 308-03 > Removal. Disassemble the transmission. Refer to WSM, Section 308-03 > Disassembly. Disassemble the input shaft to gain access to the 6th/5th gear synchronizer. Refer to WSM, Section 308-03 > Disassembly and Assembly of Subassemblies > Input Shaft. Replace the 6th/5th gear synchronizer and assemble the input shaft. Assemble the transmission. Refer to WSM, Section 308-03 > Assembly. Install the transmission. 11032752
SSM 54818
May 2026 Service Bulletin/Repair Instructions POWER TRAIN Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. 11032566
SSM 54797
Apr 2026 Over The Air UNKNOWN OR OTHER 25S49 Recall Remedy: -Infotainment software update to address frozen screens 11031929
SYNC-25.1.9.7.1 Bronco
Apr 2026 Service Bulletin/Repair Instructions POWER TRAIN Some 2021-2025 Bronco vehicles built on or before 09-Sep-2025 may require replacement of the ambient air temperature sensor for various concerns. Diagnostic trouble codes (DTC) P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). A concern has been identified in TSB 26-2006 that previously instructed replacement of the incorrect ambient air temperature sensor for the vehicle application. Monitor Professional Technician System (PTS) for updates. 11031638
SSM 54781
Apr 2026 Service Bulletin/Repair Instructions POWER TRAIN This bulletin supersedes 25-2627. Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions:  Shudder chatter condition, most noticeable at low speeds turning  No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination. 11031619
TSB 26-2194
Apr 2026 Service Bulletin/Repair Instructions EXTERIOR LIGHTING Bronco Sport and Maverick vehicles utilize an advanced headlamp design that features a sharp horizontal light-to-dark transition. This is an intentional optical characteristic designed to meet safety and performance standards. This transition is a normal attribute of the vehicles lighting signature and is most visible during high-beam operation. No repair is required as the system is functioning to specification. Workshop Manual (WSM), Section 417-01 Exterior Lighting > Description and Operation > Exterior Lighting - Overview has been revised to clarify this condition as an operating characteristic of the vehicle. 11031628
SSM 54769
Apr 2026 Service Bulletin/Repair Instructions UNKNOWN OR OTHER Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). 11031487
TSB 26-2006
Apr 2026 Over The Air UNKNOWN OR OTHER 26S09 Recall Remedy -Update to enable rearview camera image to display when in reverse after infotainment screen thermal shutdown 11031652
SYNC-26.2.1.6.5.3 Bronco

What are the most common 2021 Ford Bronco complaints?

211 total complaints on record

How much does the 2021 Ford Bronco cost in fuel?

Estimated annual cost $2,590 $216/month at 12,000 miles/year
Effective efficiency 20.9 MPG
Energy used 575 gal/yr
Price assumption $4.50 $/gal

Assumptions: 20 city / 22 highway / 21 combined MPG · Regular Gasoline · efficiency ratings from official public data when available · fuel price default: official public data (U.S. average, Jun 3, 2026)

426 g/mi CO2Fuel score 4/10Smog 5/10

Model-year comparison